Hubsoft integration with BDCOM

Hubsoft, an ERP for internet service providers (ISPs), integrates with BDCOM to authorize, provision, and deauthorize ONUs on the brand's OLTs. Technicians release a subscriber's ONU from the Hubsoft screen without needing OLT credentials.

BDCOM manufactures switches and GPON and EPON equipment. With Hubsoft, the ISP authorizes and provisions ONUs on GP3600 and GP3600B OLTs from the system screen via Telnet.

Request a Demo Partner website

About BDCOM

BDCOM is an Asian network equipment manufacturer. Its portfolio includes data center, enterprise, edge, and L2 switches, as well as GPON and EPON solutions with OLTs and ONTs.

What the integration does

The integration connects Hubsoft to the BDCOM OLT via Telnet. Once the OLT is registered, the team can use Hubsoft to:

Check the ONUs connected to and pending authorization on each PON port.
Authorize the ONU linked to the customer and service, using the selected CPE profile. Provisioning runs immediately afterward, with no additional action.
Deauthorize and deprovision using the commands from the same profile.
Authorize and provision in bulk, one PON at a time, for ONUs already linked to services by serial number.
Wi-Fi name and password, including the 5 GHz network, entered during authorization when the CPE profile has Wi-Fi commands.
Custom commands after provisioning, such as adjusting Wi-Fi or enabling VoIP.
Alert when the ONU signal exceeds the limit on ports with verification enabled.
Record of commands sent to check the OLT response when something fails.

Integrated models:

GP3600 (Telnet, port 23)
GP3600B (Telnet, port 23)

What you need

A BDCOM OLT of one of the models above, with an access IP address.
The username, password, and access port for Hubsoft to connect to the OLT.
The OLT's POP registered under Network > Points of Presence.
CPE profiles with authorization, provisioning, deprovisioning, and deauthorization commands under Settings > Network > CPE Profiles.

How to activate

Under Network > Connection Equipment, click Add and enter the name, IP address, BDCOM manufacturer, model, and POP.
Enter the username, password, and access port: Telnet, port 23, for both models.
Under Actions > View, enable editing and register the PON ports in the Interfaces tab, individually or in bulk, with chassis, slot, PON, initial VLAN, VLAN increment, default CPE profile, and the concentrator that authenticates customers.
To test, open Actions > View Connected Customers and check the Layer 2 and Pending Layer 2 tabs.
Authorize the first ONU from the menu next to it by entering the customer, service, and CPE profile.

The step-by-step guide with screenshots is available in the Hubsoft wiki: OLT and port registration, ONU authorization and provisioning and integrated OLT list.

Limitations

Bulk authorization and provisioning process one PON at a time. If the PON has ONUs in bridge and router mode, process one type at a time.
When registering ports in bulk, register no more than 4 slots at a time.
When changing PONs, deauthorize the ONUs from the old PON directly on the OLT. In Hubsoft, deauthorization also removes the link between the customer and the ONU.

Frequently asked questions

My BDCOM model isn't on the list. What now?

Contact Hubsoft's Infra Support team. They will assess whether the model can be integrated.

Does the technician need the OLT password?

No. The username and password are stored in the equipment record. The operator can view and authorize ONUs from the Hubsoft screen without the OLT credentials.

Can I authorize multiple ONUs at once?

Yes, one PON at a time, under Actions > View Connected Customers. The ONUs must be linked to customer services, with the serial number entered in the service's Authentication tab. After bulk authorization, bulk provisioning applies the CPE profile and VLAN.

Reviewed on 10/10/2026.